In SCB13-1000\/10, S identifies a three-phase transformer, C the cast-resin construction, and B the foil-winding designation. The 13 identifies the design series; 1000 and 10 identify the nominal kVA and primary-voltage class in this example.<\/p>
SCB10, SCB11 and SCB13 name the cast-resin family. The full equipment specification also states secondary voltage, frequency, connection, cooling and accessories so the model code can be read alongside the actual project duty.<\/p><\/div><\/details><\/div><\/section>Two construction arrangements<\/h2>Open dry-type assembly<\/button>Cast-resin windings<\/button><\/div><\/span>Dry-type core and winding assembly<\/h3>Front view of the three-column dry-type assembly and its base-mounted fans.<\/figcaption><\/figure>The dry-type product is illustrated as a three-column core and winding assembly. Connections are arranged above the windings, and fans are located along the base. This arrangement brings the winding assembly, connection points and cooling hardware into a single equipment envelope.<\/p>
For integration into a cabinet or an equipment room, the useful interfaces are the mounting position, cable approach and access around the winding assembly. The installation layout should allow the terminal area and cooling hardware to be reached without obstructing the equipment\u2019s airflow paths.<\/p>
The upper connection area and the fan assemblies occupy different service zones. Cable entry, terminal access and the surrounding enclosure can be arranged around these zones while leaving the winding and cooling paths accessible.<\/p>
Dry-type Isolation Transformers<\/path><\/svg><\/button><\/div><\/div><\/div><\/div><\/div><\/span>Vacuum-cast insulation and supported windings<\/h3>Angled view of the cast-resin winding assembly, upper terminals and base-mounted fans.<\/figcaption><\/figure>The epoxy resin cast isolation family includes SCB10, SCB11 and SCB13 series designations. Its windings are cast and cured under vacuum, forming a solid resin insulation structure around the conductors. The construction combines a grain-oriented cold-rolled silicon-steel core with copper foil or copper conductors.<\/p>
Steel clamps and supports position the core and winding assembly. A protective coating is applied to these structural parts. The result is an oil-free assembly for indoor installation, with the winding, core and supporting structure arranged for connection to the surrounding distribution equipment.<\/p>
Capacity, voltage ratio and impedance are project configuration items. Enclosure protection and accessories are also selected for the installation, so the final equipment specification describes the complete assembly rather than relying on a series name alone.<\/p>
SCB Epoxy Resin Cast Isolation Transformers<\/path><\/svg><\/button><\/div><\/div><\/div>Capacity and voltage ratio are specified for the selected configuration.<\/p><\/div><\/div><\/div><\/div><\/section>Electrical isolation and system interfaces<\/h2>Separate circuits<\/button>Earthing & screening<\/button>Ratings & interfaces<\/button><\/div><\/span>Electrical isolation and the secondary system<\/h3>Separate circuits<\/h3> An isolation transformer transfers energy through the magnetic field in its core. The primary and secondary windings form separate conductive circuits, allowing the supply-side and load-side winding arrangements to be specified individually.<\/p><\/div>
The required voltage ratio<\/h3> The voltage ratio is a separate design parameter: electrical isolation does not require a fixed 1:1 ratio. The installation design also establishes the secondary connection, earthing arrangement and protection. These system decisions remain relevant to the equipment connected to the transformer.<\/p><\/div>
Secondary system coordination<\/h3> The secondary circuit is coordinated with the installation\u2019s earthing and protective devices. A neutral connection, protective-earth connection and any screen earth have different roles; the connection drawing identifies each interface and the intended arrangement for the load.<\/p><\/div><\/div><\/div><\/div>
Connections, earthing and electrostatic screening<\/h3>Isolation and screening<\/h3> Electrical isolation and interference attenuation describe different requirements. Separate winding circuits establish isolation. An electrostatic screen, when included in a transformer design, is an additional component between winding circuits and requires an appropriate grounding connection.<\/p><\/div>
The interference requirement<\/h3> For sensitive equipment, an interference requirement should identify the noise type, frequency range and grounding arrangement. An attenuation value or a screened construction should appear in the agreed configuration before it is treated as a product performance characteristic.<\/p><\/div>
Connection and bonding<\/h3> Bring the supply connection, secondary load connection and equipment bonding into one interface drawing. If a screen is required, include its earth termination and the intended test conditions in that drawing; cable routing and the surrounding installation remain part of the interference assessment.<\/p><\/div><\/div><\/div><\/div>
Electrical ratings and installation interfaces<\/h3>Electrical and mechanical duty<\/h3> A useful transformer specification connects the electrical load to the physical installation. Capacity and the primary-to-secondary voltage ratio establish the basic duty; frequency, connection arrangement and impedance define further system requirements. Enclosure and mounting details then place that electrical design within the available space.<\/p><\/div>
The connected load<\/h3> The connected load can affect the specification as well as the steady-state demand. Motor starting and other inrush conditions influence the permitted voltage drop. Where nonlinear loads are involved, their operating characteristics should be included in the load description so the transformer design can be assessed for the actual duty.<\/p><\/div><\/div><\/div><\/div><\/div><\/section>
![\"Transformer](\"https:\/\/subiapower.com\/wp-content\/uploads\/2026\/09\/subia-group-production-workshop.webp\")